Payment & Shipping Terms:
|MOQ:||1PCS Cable Reel||Cord Length:||70 Ft.|
|Cord Included:||No||Max Pressure:||300|
|Reel Grade:||Light Duty||Drive Type:||Spring|
|Hose I.D:||3/8"||Product Name:||LC607 OLS Spring Retractable Stainless Steel Hose Reel|
cable reel drum,
extension cable reel
JARCH's new Series LC stainless steel hose reels are developed for light-duty, spring-driven hose reel applications in corrosive or sanitary environments. Designed for stationary indoor and outdoor use, these reels can be attached to most surfaces that can be drilled. The reel is built with high quality stainless steel components for maximum corrosion resistance. The four base slots allow the reel to be easily mounted or adjusted. The eight position ratchet locks the reel at the desired hose length while the guide arm adjusts to five convenient positions. **Series LC reels have a brass swivel.**
***Robust construction - Base and guide arm made of heavy-gauge steel stampings with reinforcing ribs;
***Corrosion resistant - High quality stainless steel components;
***Easy mounting - Base slots to facilitate mounting and adjustment;
***Latch spring - Field-proven torsion spring, stainless steel construction.
Cable reel roller rack reel drum Spring Driven Hose Heavy Duty Cord Reel with LED light and USB
Jarch main products:
|Packaging Details:||Standard Export carton Package|
|Delivery Details:||Delivery time for Sample: 3 days / Delivery time for Order depends on quantity
Shipping:BY DHL, FedEx, UPS or TNT......
Adding wraps of hose will increase spring tension. This can be accomplished by pulling out approximately 10 feet of hose, hand feed hose back up through roller bracket assembly* until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.
This can be accomplished by removing wraps of hose from the reel sheave. Remove wraps of hose from the sheave, one wrap at a time, until desired tension is obtained.
*For Series D9000 reels, you will have to remove the bumper and control handle then feed end of hose through roller bracket assembly to add or remove wraps of hose from the reel drum.
Insufficient spring tension
Adjust spring tension by adding wraps of hose. Pull out approximately 10 feet of hose. Hand feed hose back up through roller bracket assembly until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.
Hose / cord reel mounted on ceiling above 16 feet
Must special order heavier gauge spring steel for drive spring to overcome weight of hose / cord extending from reel. Control handle weight must also be considered. Contact Reelcraft for further information.
Latch mechanism engaged with drive spring coiled to solid height
U-bolt hose clamps on sheave assembly not positioned correctly.
Hose / cord fully extended will not retract
Latch mechanism engaged with drive spring is coiled to solid height. U-bolt hose clamps on sheave assembly are not positioned correctly.
Product supply to reel, rigid, plumbed in
If flexible connecting hose is not used between hose reel inlet and hard plumbing, you stand the chance of causing excessive bind to main shaft and hub bearings causing reel not to retract. This also voids warranty.
Reel mounted on uneven surface
Bolting the reel down to an uneven surface will distort side frame causing a bind on main support shafts restricting smooth retraction of hose.
Wrong guide arm position
If guide arm is in side wind position for ceiling mounted reels, hose / cord is bending at a 90° angle over roller bracket assembly causing excessive loss of spring tension. Adjust guide arm to coincide with how hose / cord reel is actually mounted. U-bolt clamps may need to be adjusted accordingly.
Broken main spring, broken spring arbor, corrosion on shaft and hub
Replace broken part with new. For corrosion: disassemble reel and remove corrosion, lubricate and reassemble.
U-bolts tightened down too tight on hose restricting product flow. Loosen U-bolts to be snug on outside diameter of hose but not too much that it crimps off product flow.
This could mean it has a broken latch spring, bent latch pawl or latch plate. The broken part(s) will need to be replace.
If you have any questions, pls contact us without any hesitation.